Ordering: Fiber Optic Cable
Assemblies and Accessories

Fiber Optic Information

Low cost, best quality, leader in fiber optic technology for over 14 years!!

RLH Industries, Inc. has been a leader and innovator in fiber optic technology for more 14 YEARS. We are aware that high quality and fast delivery are extremely important. We can meet your tight deadlines. We have the capability to service your existing fiber optic cables or jumpers or can manufacture a wide variety of custom fiber optic cable assemblies, such as:

Optical-node                                               Indoor or Outdoor Cables

       Distribution                                              Breakout

            Multimode                                               Single mode

                Assemblies with pulling eyes                 Aerial

                     Fiber optic jumpers to any length         Conduit

Ordering Information:

When ordering RLH Fiber Optic assemblies, use the following table of abbreviations:

RLH= FiberCount= PlacementType= FiberType= ConnectorStyle= Length=
Manufacture Number of Fibers C=Conduit A=Aerial MM or SM ST, SC, SMA,
FC, FDDI		 In Feet
Example of assembly part number: RLH06CMMST900FT
6 Fiber, Conduit type, Multimode, ST Connectors, 900feet in length


CABLE ASSEMBLY HARDWARE AND ACCESSORIES:

PART NO.


DESCRIPTION


8806-PSH


PULLING SHEATH (Installed) - Required on one cable end for all installations.

8806-MMC MULTIMODE CONNECTOR (Installed)
8806-SMC SINGLE MODE CONNECTOR (Installed)
8806-MMPT MULTIMODE PIGTAIL (W/CONNECTOR) - One required for each fiber of an UNTERMINATED cable end. 6 Ft
8806-SMPT SINGLE MODE PIGTAIL (W/CONNECTOR) - One required for each fiber of an UNTERMINATED cable end., 6 Ft
8806-02BRK 2 FIBER BREAKOUT (Installed) - One required on each end of a 2 fiber cable.
8806-06BRK 4&6 FIBER BREAKOUT (Installed) - One required on each end of a 4 or 6 fiber cable.
8806-12BRK 8&1 2 FIBER BREAKOUT (Installed) - One required on each end of a 8 or 12 fiber cable.
8806-24BRK 24 FIBER BREAKOUT (Installed) - One required on each end of a 24 fiber cable.
SELF SUPPORTING CABLE POLE MOUNTING HARDWARE:
The following equipment is REQUIRED for aerial installations of fiber optic cable:
 

Mini Support Bracket
Mini Support Bracket

RLH P/N# 8806-1377-01

Used to support fiber optic cable on span poles.
Mounting is accomplished by simply bolting support onto telephone pole. After fiber optic cable is in place it is secured with pressure clamp and rubber split tubing supplied with bracket.

 Mini Dead End Support        RLH P/N# 8806-1375-01

Mini dead end supports are installed on telephone poles for routing fiber optic cable up to or down from dead end.
A black nylon wedge, supplied with the dead end, is used to secure cable inside stainless steel dead end housing.
Place nylon wedge around fiber cable then wrap a small piece of electrical tape around nylon wedge to temporarily hold it in place.
Position dead end around fiber cable and slide it onto the nylon wedge. Make sure fiber cable is routed under stainless steel cable loop for proper Fiber routing down Pole.
After pushing nylon wedge into dead end housing by hand, tap wedge with hammer to secure fiber optic cable in dead end.
Secure stainless steel cable loop onto telephone pole with ram hooks or proper hardware then route fiber optic cable down telephone pole. Place orange fiber optic cable identifier label around cable.
*When routing fiber optic cable up or down from dead ends, use schedule 80 or equivalent PVC to protect against damage from pole climbing or impacts.
8806-1375-01 DEADEND-Req'd each end pole. (GTE#38009898)
8806-1377-01 DIELECTRIC SUPPORT - One required for each intermediate pole. (GTE#38009901)
8806-TQTOL TORQUE TOOL - Needed for proper installation of dielectric supports. (GTE# 38009900)
FIBER OPTIC CONNECTOR PART NUMBERS AND DESCRIPTIONS

8806-2003-01        ST, MULTIMODE, COMPOSITE, PRE., 125um, W/3.0 BOOT
8806-2004-01        ST, MULTIMODE, CERAMIC, PRE., 125um W/3.0 BOOT
8806-2005-01        ST, MULTIMODE, CERAMIC, PRE., 140um, W/3.0 BOOT
8806-2006-01        ST, SINGLEMODE, CERAMIC, PRE., 125um W/3.0 BOOT
8806-2007-01        ST, SINGLEMODE, CERAMIC, PRE., 126unt, W/3.0 BOOT
8806-2008-01        ST, SINGLEMODE, CERAMIC, PRE., 127um, W/3.0 BOOT
8806-2011-01        SC, SINGLEMODE, CERAMIC, 125um W/3.0 TB
8806-2012-01        BNC, MULTIMODE, STAINLESS STL., 125um, W/3.0 TB
8806-2100-01        SMA, MULTIMODE, STAINLESS STL., 125um, W/3.0 TB
8806-2107-01        FDDI, MULTIMODE, CERAMIC, 125um W/5.0 TB
8806-2108-01        FDDI, MULTIMODE, CERAMIC, 125um, 2 BY 3.0
8806-2130-01        ST TO ST COUPLER, SINGLEMODE (FEMALE)
8806-2131-01        ST TO ST COUPLER, MULTIMODE, (FEMALE)
8806-2132-01        ST TO ST COUPLER, MULTIMODE FLANGE (FEMALE)
8806-2133-01        SMA (905/906) COUPLER, MULTIMODE, THREADED
8806-2160-01        .3um POLISHING FILM, 8 BY 10 INCH SHEET
8806-2161-01        1um, POLISHING FILM, 8 BY 10 INCH SHEET
8806-2162-01        3um, POLISHING FILM, 8 BY 10 INCH SHEET
8806-2163-01        5um, POLISHING FILM, 8 BY 10 INCH SHEET

*900um BOOTS AVAILABLE UPON REQUEST